Analysis Configurations¶
This page contains schemas used in configuring analysis functions.
CorrectionFactorDataInputs¶
Defines a set of data corresponding to a combination of sensors used in a correction factor measurement.
type |
object |
|
additionalProperties |
properties |
|
|
||
|
||
|
||
correction-factor-measurements¶
Points to a DUT’s S-parameters, parsed RF sweep, and calorimeter sensitivity coefficients for a particular measurement.
properties |
|
|
|
|
|
|
|
additionalProperties |
false |
RFSweepParserConfig¶
Settings needed to parsed an RFsweep.
type |
object |
|||
properties |
||||
|
type |
object |
||
properties |
||||
|
Used for determining the relative time delays between the instrument signals for finding the ‘correct’ RF switching time. A typical value is 5 seconds. |
|||
type |
number |
|||
|
Override the stats window (in seconds) to average over when evaluating long timescale RF off values. If not provided will use the stats_window size in the measurement configuration. |
|||
type |
number |
|||
|
Enables performance of fast off analysis for thermoelectric sensors. Usually only DUTs, if provided must provided V_off settings. |
|||
type |
boolean |
|||
|
What time should be used when evaluating the V_off fit to find the off value, time is relative to when power is switched off. Only needed for DUTs |
|||
type |
number |
|||
examples |
0.37 |
|||
|
What type of fit function to use when fitting to the fast off voltage of the sensor. Only needed for DUTs |
|||
type |
string |
|||
enum |
single_sample, lin_plus_exp, linear |
|||
examples |
linear |
|||
|
The time window - relative to when power was turned off - to fit the data to. Should be large enough to capture the curve. Only needed for DUTs. |
|||
type |
array |
|||
examples |
1 |
|||
20 |
||||
items |
type |
number |
||
maxItems |
2 |
|||
minItems |
2 |
|||
ParsedDCSweep¶
type |
object |
properties |
|
|
|
|
|
additionalProperties |
|
ParsedRFSweep¶
Output of a parsed calibration measurement. Each output is a an RMEMeas object with shape (n,) where n is a coordinate dimension called (frequency) in GHz and the outputs are real valued numbers corresponding to the measurement result.
type |
object |
properties |
|
|
Calorimeter thermopile voltages in RF off state. |
|
Calorimeter thermopile voltages in RF on state. |
|
Final value of the RF source. |
|
Power inferred by the thermopile in calorimeters RF off state. |
|
Power inferred by the thermopile in calorimeters RF on state. |
|
Uncorrected effective efficiency of sensor 2 (internal DUT) |
|
Thermopile voltages of sensor at port 2 in RF off state. |
|
Thermopile voltages of sensor at port 2 in RF on state. |
|
RF power measured by sensor 2 (internal DUT) nn during the fast RF off portion of a frequency point. |
|
RF power measured by sensor 2 (internal DUT) nn during the slow RF on portion of a frequency point |
|
RF power measured by sensor 3 (external sidearm) nn during the fast RF off portion of a frequency point. |
|
RF power measured by sensor 3 (external sidearm) nn during the slow RF on portion of a frequency point |
|
RF power measured by sensor 2 (internal DUT) nn during the fast RF off portion of a frequency point. |
|
RF power measured by sensor 2 (internal DUT) nn during the fast RF off portion of a frequency point. |
|
RF power measured by sensor 2 (internal DUT) nn during the slow RF on portion of a frequency point |
additionalProperties |
true |
Historical Eta Measurements List¶
Describes historical Eta measurements to be used when calculating/reviewing Eta measurements.
type |
object |
properties |
|
|
All properties are key value pairs with the name of the measurement as a key, and the value an EtaLike object. |